Rogers Modem Bridge Mode Set Up

Do you wish to set up Bridge Mode on your Rogers Modem? People usually do this when they want to use internet equipment other than that which is provided by Rogers. In Bridge Mode, it will mean that your modem will only be working as a modem and not as a router. Remember that the devices that Rogers provides at the moment are combination router-modems. So, in Bridge Mode, you will be switching off the router function. Rogers uses many different modems. We show you how to set up Bridge Mode on the following models;

Rogers Ignite Modem Bridge Mode

The Ignite Gateway (Arris XB6) is the latest piece of hardware being offered to Rogers customers. Like all the other devices featured here, it’s a combination modem router. To set up the Rogers Ignite bridge mode, you need to take the following steps;

  • Go to a browser on your computer.
  • Type into the address bar and press enter.
  • Log in using the Ignite password and username.
  • Click on Gateway then on At a Glance.
  • On Bridge Mode, click on Enable.
  • Your Gateway will now stop functioning as a router. Now you can connect your own router or other equipment.

Rogers EERO Bridge Mode

Do you have the Eero WiFi system set up in your home or office? So, how do you set up Eero bridge mode? Bridge mode on the Eero means your modem’s WiFi function will be turned off. You will be getting WiFi via the Eero. Bridge mode on the Eero is switched on using the Eero App. The following are the steps for doing so;

  • Open the Eero app and click to expand the hamburger menu.
  • Click on Network settings
  • Next, click on Advanced settings.
  • Click on DHCP & NAT.
  • Select Bridge Mode.
  • Save your changes.

Hitron CODA 4582 Modem Bridge Mode

If you have the Rogers Hitron CODA 4582, the following is how to set up Bridge Mode;

  • Type in the address bar of Chrome, Edge or any other browser on your computer.
  • Press enter.
  • Log in using the details given here.
  • Click on Basic.
  • Next, click on Gateway Function.
  • From there, click on Residential Gateway Function.
  • Next, click on Disable.
  • Confirm by click on OK.

Rogers Hitron CGN3AMR, CGN3, CGN3ACR, CGNM3552 Modems Bridge Mode

The Rogers Hitron CGN3AMR, CGN3, CGN3ACR, CGNM3552 are similar regarding how to set up bridge mode. If you have any of these modems in your home or office, the following is how to bridge them;

  • Type into the browser on your computer and press enter.
  • Log in using the Rogers router login details given here.
  • Click on Basic.
  • Click on Gateway Function.
  • Click on Residential Gateway Function.
  • Click on Disable.
  • Click on OK to confirm your changes.

Hitron CGN2 Modem Bridge Mode

So, how do you set up the Rogers modem bridge mode if you have the Hitron CGN2 Modem? The following are the steps for getting bridging the CGN2;

  • Use an Ethernet cable to connect to your internet.
  • Open any browser and type into the address field before pressing on enter.
  • Log in using the default Rogers router password and username given here.
  • Once logged in, click on Basic Setup.
  • Next, click on Capability at the top.
  • Then check Residential Gateway function and click on Apply.

How to put the Cisco DPC3825 Modem into Bridge Mode

The Cisco DPC3825 Modem is another piece of equipment that Rogers supplies to its customers. To put the DPC3825 into Bridge Mode, you need to take the following steps;

  • Type into the address bar of your browser. Any browser will do. Press enter when done.
  • On the login page for your router, use the default details given here to log in.
  • Next, you need to click on Administration.
  • On Working Mode, switch to Bridged Only.
  • Save your settings.

How to Put the SMC D3GN Modem into Bridge Mode

Many Rogers customers have the SMC D3GN. So, what are the steps for bridging this modem? The following is how to bridge the Rogers SMC D3GN Modem;

  • In the address bar of your browser, type and press enter.
  • Log in using the details given here.
  • Select System in the top left menu.
  • Make sure Disable All Commercial Gateway Functions is ticked.
  • Click on Apply.

How to get out of bridge mode

That’s the Rogers modem bridge mode setup. We noted that you may be looking to bridge your Rogers router if you have brought your own equipment to the network. Perhaps you have a router that you think works great and will be faster than the equipment provided by Rogers.

Or maybe you are looking to save on rental and purchase fees by using a router that you already had. However, you could find, after a while, that the equipment provided by Rogers is the best after all.

The major challenge with bringing your own equipment is that you don’t get any Support. Should something go wrong, you will be expected to sort it out on your own. That’s viable if you are tech savvy. But for the uninitiated, that can become rather challenging.

That’s the reason why many people end up changing their mind. A lot of people out there are looking at how to get out of Bridge Mode on their Rogers modems. The thing to remember is that Bridge mode is off by default. You actually need to turn it on to get the functionality that you are looking for.

So, it then follows that to get out of bridge mode, all that you need to do is to do a factory reset on your Rogers router. Press on the reset button at the back of the device. Hold the button for about 10 seconds. Your Rogers router will now go back to factory defaults, meaning bridge mode will be disable. From there, the modem’s router functions will be restored.


In this article, we gave you the Rogers modem bridge mode setup steps. We noted that Rogers provides combination router-modems to it’s clients. However, some people want to bring their own routers to the network. To do that, you need to bridge the modem that you got from Rogers. That means the modem will now only work as a modem and not as a router. You will then be able to connect your own router.

Leave a Reply

Your email address will not be published. Required fields are marked *